I) Key dates

II) PerfectPower version history

     A) PerfectPower Android

     B) PerfectPower iOS

 

 

 

I) Key dates

 

Mon 02012012: Creation of PerfectPower iOS starting from 0

Mon 02072012: Release of PerfectPower iOS 1.0 on the App Store

xxxx2012 (date to be found): Creation of the PerfectPower official website: www.perfectpower.ch

 

Thu 02012014: Creation of PerfectPower Android starting from 0

Sat 09082014: Release of PerfectPower Android 1.0 on the Android Market (ex Google Play Store)

 

Wed 02102019: Temporary withdrawal of both programs (3 years) for installation in the USA

 

Mon 01112021: "Official" installation in the USA (in Union City, New Jersey)

Thu 16122021: Creation of a new official website in anticipation of the return of PerfectPower

 

Fri 13012023: Return of PerfectPower Android on the Google Play Store (new version 6.0)

Sat 20052023: Return of PerfectPower iOS on the App Store (new version 5.0)

Thu 28092023: PerfectPower Android officially compatible with RaceBox devices

Sun 01102023: Creation of the PerfectPower Instagram account perfectpower747

 

Wed 27032024: Inauguration of a new “New generation” website: www.perfectpower.pro

Thu 11042024: Release of PerfectPower Androïd 7.0, the ultimate version in measurement accuracy

Wed 01052024: Launch of a friendly challenge at 10,000 euros & dollars

Sun 12052024: Release of PerfectPower iOS 6.0, the ultimate version in measurement accuracy

 

End of March 2025: Release of PerfectPower iOS 7.0, identical to PerfectPower Android 7.0

April 2025: Crossing the USA with a PerfectPower car

 

 

 

II) PerfectPower version history

 

This history is the official history of PerfectPower. It is extremely detailed for a perfect understanding of what each new version brings. The version reports published on the Google Play Store and the App Store are often a short version of the official reports presented here.

 

Note 1: While waiting to find the databases of the old PerfectPower official website (2012-2020), the current history begins with versions Android 6.0 and iOS 5.0 which marked the return of PerfectPower on the sales platforms in 2023 after 3 years of absence.

 

Note 2: All release dates are given in New York time zone (PerfectPower standard).

 

A) PerfectPower Androïd

 

V 7.1.1

Mon 23/12/2024 - 12.32 pm

 

1) Performances Simulator:

- Tiny optimization: Taking into account the inertia of the car and the pneumatic "un-slip" during gear changes (tiny improvement in acceleration and run flying start times with gear changes) (see note below)

- Use of the parameters of the Car sheet and no longer those of the Results sheet which must imperatively be reserved for the re-calculation of power results on parameters

- Minor corrections of FR/EN texts

2) Power Results Sheets: Catching up on an oversight in the last version 7.1: The measurement re-calculation function is now also automatic for the correction norm, and then now covers all cases (4):

- Changing the correction norm

- Closing the keyboard after modifying car or weather parameters

- Activation / Deactivation of the max speed correction (mode 1)

- Activation / Deactivation of the road slope correction (mode 2)

 

Note. This tiny optimization of the performances simulator was made possible thanks to an extremely precise comparative analysis of detailed Dragy Box times (100-110, 100-120, ..., 100-200) of a 100-200 km/h achieved with a BMW 335i F31 stage 3 in automatic 8-speed gearbox and the PerfectPower performances simulator, which revealed exceptionally close times (often identical to the hundredth!) on the phases where no gear was changed, but a tiny but certain pessimization of the simulator on the phases with gear change, even though the gear change time was known to the hundredth and the max revs programmed in the automatic 8-speed gearbox of this BMW were the ideal max revs of the PerfectPower performances simulator...

A huge thanks to the owner of this BMW (a Czech tuner) who made this tiny optimization possible, and who for info confirms on his own experience (hundreds of measurements with the Dragy Box!) the perfection of the ideal max revs of the PerfectPower performances simulator, much better than those of the models he had used until then!

 

V 7.1

Mon 23/09/2024 - 10.55 am

 

1) Power / Mode 2 only: Addition of a function of results correction on road slope, with indication of the average road slope and the max correction applied

However, the use of the RaceBox Mini is essential to use this function, the internal GPS of phones being much too inaccurate for an accurate correction!

Moreover, this function is NOT a magical function allowing to exempt you from performing measurements in both directions of the road since although it compensates with impressive efficiency for the effects of road slope, on the other hand it does not compensate for those of the wind (just as important!) AND therefore it remains ESSENTIAL to perform measurements in both directions of the road and average them to obtain perfectly reliable results, thank you for your understanding!

2) Power: The manual function of measurement re-calculation becomes automatic in all cases:

- Closing the keyboard after modifying car or weather parameters

- Activation / Deactivation of the max speed correction (mode 1)

- Activation / Deactivation of the road slope correction (mode 2)

==> Removal of the "Re-calculation of the measurement" button

However, be careful, you must ALWAYS remember to save any modification (car parameters, max speed correction, road slope correction) that you wish to keep via the "Register the new parameters" button BEFORE leaving the results sheet, thank you. This function may however also become automatic in the future if this choice was preferred by users.

 

V 7.0.6

Tue 27/08/2024 - 9.18 am

 

1) Lap Timer: Fixed an oversight in the adaptations to Android 14 made in the previous V7.0.4, which generated a crash when trying to use Bluetooth to connect to a RaceBox Mini & Mini S under Android 14

 

V 7.0.5

Mon 26/08/2024 - 9.10 am

 

1)All power and performances measurements: Fixed an oversight in the adaptations to Android 14 made in the previous V7.0.4, which generated a crash when trying to use Bluetooth to connect to a RaceBox Mini & Mini S under Android 14

2) Fixed a bug that could occur when disconnecting from the RaceBox Mini & Mini S while it is out of Bluetooth range or discharged

3) Minor changes of some help texts for runs flying start & braking & losses measurement measures

 

V 7.0.4

Sun 04/08/2024 - 3.03 pm

 

1) All adaptations to Android 14 (API 34)

2) Power results sheets: Management of an information button on the max speed correction function

 

V 7.0.3

Sun 05/05/2024 - 11.51 am

 

1) Power / Mode 1 only: Addition in the power results sheets of the info "Speed at max rev" and an explanatory text on the "Max speed correction" function ideal in the event of poor GPS reception or failure of this one in this mode (indeed, 95% of the measurement accuracy is made by the accelerometer in this mode)

2) Power / Modes 1 and 2: Addition in the power results sheets of a “Miscellaneous” chapter and its first information: “Estimated tyre slip”

3) Fixed an oversight (non-deletion of internal logs after release of the V7.0.2) which could cause a crash when opening certain results

 

V 7.0.2

Thu 25/04/2024 - 9.27 am

 

1) Power & Accelerations / Modes 1 and 2: Tiny optimization of the smoothing of curves, even cleaner but without any loss of precision

Note: This first modification was decided out of pure perfectionism!

2) Power & Accelerations / Mode 2 only: Specific but necessary slight increase in the smoothing of curves in mode 2 so with the RaceBox Mini

 

V 7.0.1

Fri 12/04/2024 - 1.35 pm

 

1) Fixed an oversight distorting the calculation of wheels power for results of type "Incorrect average of version V6"

2) Improved measurement mode management:

- Added measurement mode to power results lists

- Specification of the measurement mode for each validated result in the power results comparison sheets

3) Aesthetic improvements:

- Fixed an oversight disrupting the display in cars and results lists in dark mode on some phones

- Wallpaper of cars and results lists in black (instead of white)

 

V 7.0

Thu 11/04/2024 - 6.11 pm

 

Major evolution of the V7 version compared to the V6 version:

1) Ultimate and final optimization of the precision of power and acceleration measurements in modes 1 (Accelerometer + GPS) and 2 (GPS only)

A) Return to the signal processing techniques of versions V1 to V5, just deeply reworked and optimized!

Indeed, these techniques have the huge advantage of generating absolutely no lag in the curves, unlike that introduced in the V6 version, which caused a slight permanent delay resulting in a slight underestimation of maximum torques and a slight delay in maximum power and maximum torque revs...

B) Optimization of the curves smoothing, allowing both to faithfully reproduce the exact behavior of the engine (AND without any lag as explained above!), AND to completely destroy all disturbances (engine vibrations and "road disturbances" in the mode 1 "Accelerometer + GPS", and "GPS noise" in the mode 2 "GPS only")

C) Power only: Optimization of the detection of the exact point of end of measurement (rev limiter -on gasoline engine- or foot lift), allowing in one of the next versions 7.0.X the addition of the information "Estimated tyre slip"

D) Power only: Conservation and optimization of the system of variable smoothing of the curves depending on the signal / noise ratio (introduced in the V6 version, and allowing an optimal curves precision in all circumstances and the equalization of curves precision in 2nd and in 3rd gear), giving in comparison with the calibration carried out in the V6 version slightly "un-smoothed" curves 

E) Accelerations only: Removal of the system of variable smoothing of the curves depending on the signal / noise ratio (introduced in the V6 version), because it is unsuitable for acceleration measurements in gear change phases ==> Return to the fixed smoothing of versions V1 to V5 but optimized, giving in comparison with the calibration carried out in the V6 version significantly “un-smoothed” and much more realistic curves

F) Mode 2 (GPS only with use of the RaceBox Mini & Mini S) only: Resolution of a double (or even triple) points problem!

Indeed, the RaceBox Mini & Mini S is clocked at 25 Hz, but if in absolute terms it returns 25 information per second, in reality certain points are repeated two (or even three) times, which reduces its effective frequency (up to "only" 15 Hz!) and can obviously disrupt their correct processing, so here is what has been done:

- Search for all these "fake" double or triple points

- Clean re-calibration of measurement times and GPS speeds

Thus, PerfectPower can exploit the information from the RaceBox Mini & Mini S to its full potential, which is not quite that officially announced (25 Hz)...

2) Re-calculation and re-saving of all single (= individual) results saved in your phone during their first opening with this V7 version: thus, absolutely all your old measurements are converted in the blink of an eye to the new calculation system of the V7 version, exactly as if you had performed them directly with it!

IMPORTANT: It is therefore NORMAL to note that all your single results will change (the maximum powers will be approximately the same, but the maximum torques will slightly increase), but these are for sure the good AND final ones of the V7 version!

3) Specific management of all averaged results produced with version V6: as these results cannot be re-calculated with the new calculation system of version V7, they are kept as is and will therefore not change, but they are stamped " Incorrect average of version V6"

IMPORTANT: For the sake of transparency, the possibility of comparing these "incorrect" averaged results of version V6 with the other "normal" results of version V7 (both single and averaged) is offered to you: it is thus possible for you to visualize very precisely the difference in results between those of the V7 version which are absolutely perfect (and in particular without any lag!) and those of the V6 version suffering from a slight lag... be careful, however, to only compare results performed exactly in the same conditions (the ideal being to compare an "incorrect average of version V6" with the new average recalculated with version V7 and of course with the same source measurements!) otherwise the comparison will be distorted!

 

V 6.2.2

Fri 22/03/2024 - 2.52 pm

 

1) All adaptations to Android 13 (includes taking into account the new stricter Android rules on the full frequency use of the phone's sensors)

2) Optimization of the Bluetooth permissions management system for phones running Android 12 or +

3) Aesthetic improvements to the Setup screen and all associated screens, cars list, and results lists: White background (instead of green)

 

V 6.2.1

Mon 04/03/2024 - 4.30 pm

 

1) Fixed a bug preventing the Bluetooth scan from being launched for phones running Android 12 or +, even when authorization has been granted

 

V 6.2

Sun 03/03/2024 - 3.03 pm

 

1) Addition of a new “GPS only” measurement mode (power & accelerations & braking measurements) allowing the only use of GPS data and therefore allowing to get rid of constraints of the accelerometer, thus allowing:

- to perform power measurements on a rolling start (indeed, the accelerometer calibration phase at standstill is no longer necessary!)

- to no longer have to carry out the accelerometer calibration phase while driving for braking measurements

- to completely free the phone from any mounting requirements (stability, vibration level, positioning)

However, the use of the RaceBox Mini is essential to use this mode, the internal GPS of phones still limited to 1 Hz in 2024 being still far too slow!

2) Revision of the results comparison and averaging management system (power, accelerations, runs flying start, and braking)

3) Adding a system for requesting permission to use Bluetooth for RaceBox Mini & Mini S users under Androïd 12 or + (mandatory with the new Androïd rules! otherwise the system crashes the application during any attempt to use it)

 

V 6.1.7

Thu 25/01/2024 - 12.49 pm

 

1) Fixed a minor bug prohibiting the averaging of averaged results from 2024 and distorting the comparison of averaged results from 2024 (the values were modified). The reason for this bug was the following: PerfectPower interpreted (wrongly!) averaged results from 2024 as results performed with a version prior to version 6.0 of 13012023, and it was therefore looking to convert them to the new PerfectPower calculation system introduced in version 6.0!

2) Modification of the home message to ask RaceBox Mini users transferring PerfectPower from a phone running Android 11 or - to a phone running Android 12 or + to allow PerfectPower to connect to devices via Bluetooth in the phone settings before being able to connect to their RaceBox Mini

 

V 6.1.6

Sat 23/12/2023 - 11.28 am

 

1) Change in precision of pressure units: The hPa remains with a precision of 1 digit after the decimal point, but the in Hg and PSI go from 1 to 2 digits after the decimal point

2) Modification of the chapter “Help completing the Car sheet” in the Car sheet: Link to the Database section of the website + Descriptive text

3) Correction of an oversight: The maximum S.Cx allowed for recalculation of results after measurement increases from 1.5 to 3.0 m2, i.e. the same value as that allowed for entry in the Car sheet, which had already been increased from 1.5 to 3.0 m2 in a previous version to take motorhomes into account

4) Minor bug fix

 

V 6.1.5

Sun 30/07/2023 - 12.34 pm

 

1) For RaceBox Mini & Mini S users: Taking into account old low-end Android phones that badly support several Bluetooth communications at the same time thanks to a specific management of split data packets

2) Aesthetic optimizations:

A) Power graphs (result, comparison, averaging):

- White screen background: New PerfectPower logo with white background, identically resuming the design of the original logo with black background

- Repositioning of the PerfectPower logo and header texts in portrait and landscape mode

B) Removal of the Action bar

 

V 6.1.4

Thu 08/06/2023 - 0.47 am

 

1) Driving of the RaceBox Mini S (following the RaceBox Mini already driven since the V6.1), however limited to the classic Bluetooth communications already carried out with the RaceBox Mini, PerfectPower requiring a permanent Bluetooth connection with the RaceBox Mini & Mini S for measurements with an optimal accuracy.

2) Adding a function for duplicating a Car sheet (useful if you often measure the same model of car!).

 

V 6.1.3

Fri 26/05/2023 - 10.51 am

 

Removal of the Power function lock, the anti-piracy objective having been achieved

 

V 6.1.2

Sun 30/04/2023 - 7.10 pm

 

1) The 6 data currently used by PerfectPower coming from the RaceBox Mini (GPS speed, timestamp, latitude, longitude, WGS altitude, and GPS accuracy) are now also used for the Lap Timer, and no longer only for the seven basic measurements (power, accelerations, runs flying start, braking, speed, rev calibration, losses measurement).

2) Power graphs:

- White screen background: New transparent PerfectPower logo

- All screen backgrounds (black / white): New logo positioning (a little lower) + Maximum logo opacity

 

V 6.1.1

Thu 20/04/2023 - 8.42 am

 

1) Four new data used by PerfectPower coming from the RaceBox Mini: latitude, longitude, WGS altitude (converted by PerfectPower to MSL altitude), and GPS accuracy. These data are purely indicative at the present moment regarding the seven basic measurements (power, accelerations, runs flying start, braking, speed, rev calibration, losses measurement).

2) Automatic disconnection of PerfectPower from the RaceBox Mini when leaving the application ==> the user no longer has to think about doing it (this disconnection was previously done implicitly by the closing of the Bluetooth service by PerfectPower, but tests have shown that this could generate occasional instability (less than 1 s) of the phone's Bluetooth system and that it is preferable to always disconnect specifically from the RaceBox Mini before exiting the application, which is then now managed automatically by PerfectPower).

 

V 6.1

Sat 15/04/2023 - 2.58 pm

 

1) Driving via Bluetooth of the RaceBox Mini (external GPS 25 Hz), allowing:

- to further increase the accuracy of PerfectPower measurements (especially the runs flying start)

- the use of the new "GPS only" measurement mode for power & accelerations & braking measurements, which will be unlocked in the version 6.2

Note: In this inaugural version, only the two fundamental data "GPS speed" and "Timestamp" are used by PerfectPower, and they are used "only" for the seven basic measurements (power, accelerations, runs flying start, braking, speed, rev calibration, losses measurement), not yet for the Lap Timer. More data and the use of these data for the Lap Timer will be added in the following versions.

2) Creation of a piracy awareness system: the Power function (the main function) is locked during the very first opening of a version of PerfectPower greater than or equal to 6.1, but it is enough to read a message about piracy awareness and then to perform a very simple manipulation to unlock it.

 

V 6.0.1

Wed 22/02/2023 - 5.27 pm

 

1) For acceleration measurements (based on the "Accelerometer + GPS" combination): Creation of a auto-adaptive smoothing of the curves according to the signal / noise ratio, allowing an optimal precision of curves at any point of the measurement (resumption of the auto-adaptive smoothing already carried out for power measurements since version 6.0)

Note: This will not change the Distance / Time (60 ft, 1/8 mile, 1/4 mile, 3300 ft) and Speed / Time (0 – 20 / 40 / ... / 200 mph) results both calculated by two mathematical operations requiring no specific smoothing (integration of the acceleration provided by the accelerometer and correlation by the information provided by the GPS), but only the Acceleration / Time curve (and as a consequence the maximum acceleration noted) which it definitely needs smoothing!

2) For users having on their phone power results performed with any version prior to 6.0 (5.6 or earlier):

- Fixed the conversion of averaged results to the new PerfectPower calculation system introduced in version 6.0 (an oversight made this conversion incomplete in version 6.0, generating underestimated max powers by about 3%)

- Automatic saving of all results (individual and averaged) converted to the new PerfectPower calculation system introduced in version 6.0 as soon as a results sheet is opened (this saving was not carried out in version 6.0, generating max powers different between that read in the sheet of a given result and that read in the results list)

Reminder: Be careful because in some cases (especially for cars taking their maximum power very close to the rev limiter), there could be anomalies on the curve end since the old end of measurement detection (that carried out in versions prior to 6.0) was imperfect, thank you for your understanding! Ideally, do not hesitate to redo two final validation measurements with version 6.0 with averaging in stride to obtain certain reference results in all points of the curve!

 

V 6.0

 Fri 13/01/2023 - 4.13 am

 

1) All adaptations to ANDROID 13 (API 33) + ANDROID min changed from 4.4 (API 19) to 7.0 (API 24)

2) Ultimate optimization of power and acceleration measurements accuracy (based on the "Accelerometer + GPS" combination)

A) Limitation of the accelerometer frequency to 100 Hz (instead of 200)

B) Optimization of the end of measurement detection (rev limiter - on petrol engine - or foot lift) (power only)

C) Optimization of the curves processing by the choice of a new, more efficient signal processing technique:

- Filtering of engine vibrations optimized

- Filtering of "road disturbances" optimized

D) Creation of an auto-adaptive smoothing of the curves according to the signal / noise ratio, allowing an optimal precision of curves in all circumstances and the equalization of the precision of curves in 2nd and 3rd gear (power only)

E) Optimization of the PerfectPower model of losses under load on the pneumatic part (power only)

F) Optimization of the PerfectPower model of rolling resistance, adapted to recent road tires (law still of type a + bV², but a and b different: these are now the average values recorded by a European test campaign in 2013 on a very large number of vehicles) (power only)

G) Optimization of the PerfectPower model of engine and wheels inertia calculation (power only):

- The calculation of the engine inertia now takes into account the number of cylinders, which gives more realistic results for all engines with more (or less!) than 4 cylinders: indeed, my old model was based on a study of several PSA (Peugeot & Citroën) 4-cylinders, which could not fully apply to engines with more or less than 4 cylinders, but the shooting is now rectified!

- The calculation of the wheels inertia is refined thanks to the optimization of my model (Renault Clio 16V wheels with aluminum rims), much finer on the geometric schematization of the moving masses. 

3) Adding a "GPS only" measurement mode (power & accelerations & braking), however locked for this version 6.0: it will be unlocked in the version 6.2

4) Replacement of the function of automatic recovery of weather data by a function of manual recovery of these data in real time and by geolocation on the reference weather site "The Weather Channel"

Note: The reasons for this choice are as follows:

- The last weather server used for the automatic recovery of weather data stopped its service overnight, a mishap that I would prefer not to see repeated...

- This type of service is chargeable beyond a certain number of connections per day, which would force me to have to pass on this additional cost to PerfectPower users, whereas it takes no more than... 20 seconds to complete yourself your own weather data (pressure, temperature, and humidity) with the new manual recovery system that I propose, including in particular the automatic conversion of the atmospheric pressure given at sea level (by standardization) into the local pressure on your measurement road: so I think this solution is the most advantageous for everyone!

5) General revision of authorizations for measurements & comparison of measurements & averaging of measurements:

- Authorization of power measurements on any gear, BUT addition of a warning message in case of choosing a gear other than 2 or 3, the only ones that should be used with a serial car

- Authorization of recalculation of results after measurement for the "Engine displacement", "Number of cylinders", Tires size" fields (previously locked)

- Averaging of power measurements having a different speed correction mode allowed

- Increasing the reading time of measurements & measurements comparison & measurements averaging prohibition text

6) Deletion of the EXPERT page and therefore of the 5 parameters associated with it (k tires, coefficients a and b of the law of rolling resistance a + bV2, engine and wheels inertia) and which were available for recalculation of results after measurement, due both to the perfection of the values and calculations of these parameters in PerfectPower 6.0 and the tiny number of users concerned (experts of the automotive sector working on particular projects)

7) Adding a warning message when opening the app about measurement accuracy, specifying the importance of using an external GPS of 10 Hz minimum and performing measurements in both directions of the road

8) Solid Lap Timer revision:

- Addition of a tracks selection system (limited to two tracks for the moment: Lurcy-Levis and Le Castellet in France), but with the possibility of a free choice of GPS coordinates

- Improvement of the ergonomics of the entry of GPS coordinates in free choice

- Prohibition of choosing a track or entering GPS coordinates during a timed session

- Authorization to launch a timed session while driving (it could only be done when stopped before)

- Maximum duration increased from 30 minutes to 1 hour

9) For PerfectPower users updating from any previous version (5.6 or earlier): Creation of a conversion system of all their old power results and all their car parameters to the new PerfectPower calculation system. However, be careful because in some cases (especially for cars taking their maximum power very close to the rev limiter), there could be anomalies on the curve end since the old end of measurement detection was imperfect, thank you for your understanding!

10) Various textual and graphic adaptations related to the additions of functions performed + Update of all web links (FR/EN guides, email contact, automotive database)

11) Increasing the maximum size for entering the "Model" and "Description" fields of a car from 20 to 25 characters

12) General aesthetic revision

 

IMPORTANT: The ultimate optimization of power measurements accuracy was consolidated by carrying out a measurements session on Friday, November 4, 2022 on a reference chassis dynamometer (a Rotronics Autoscan FI 4x4 synchronized, 120,000 euros new) with three different cars! All results at this LINK.

 

B) PerfectPower iOS

 

V 6.0.2

Mon 02/09/2024 - 4.00 am

 

1) Addition of the information "Wheel power", "Measurement time", and "Measurement distance" in the power results sheets, which will however only become operational in the next version 6.1

2) Addition of 2 warnings to the automated control system for power and acceleration measurements: GPS receiver working, GPS accuracy

 

V 6.0.1

Fri 26/07/2024 - 9.05 am

 

1) Aesthetic improvements "Part 1":

- Complete revision of all textual screens (22)

- Changed the order of results types in results lists

2) Making PerfectPower compatible with the phone's dark mode

 

V 6.0

Sun 12/05/2024 - 5.33 pm

 

Major evolution of the V6 version compared to the V5 version:

1) Ultimate and final optimization of the precision of power and acceleration measurements

A) Return to the signal processing techniques of versions V1 to V4, just deeply reworked and optimized!

Indeed, these techniques have the huge advantage of generating absolutely no lag in the curves, unlike that introduced in the V5 version, which caused a slight permanent delay resulting in an underestimation of maximum torques and a slight delay in maximum power and maximum torque revs...

B) Optimization of the curves smoothing, allowing both to faithfully reproduce the exact behavior of the engine (AND without any lag as explained above!), AND to completely destroy all disturbances (engine vibrations and "road disturbances")

C) Power only: Optimization of the detection of the exact point of end of measurement (rev limiter -on gasoline engine- or foot lift), allowing the addition of the information "Estimated tyre slip"

D) Power only: Conservation and optimization of the system of variable smoothing of the curves depending on the signal / noise ratio (introduced in the V5 version, and allowing an optimal curves precision in all circumstances and the equalization of curves precision in 2nd and in 3rd gear), giving in comparison with the calibration carried out in the V5 version slightly "un-smoothed" curves 

E) Accelerations only: Removal of the system of variable smoothing of the curves depending on the signal / noise ratio (introduced in the V5 version), because it is unsuitable for acceleration measurements in gear change phases ==> Return to the fixed smoothing of versions V1 to V4 but optimized, giving in comparison with the calibration carried out in the V5 version significantly “un-smoothed” and much more realistic curves

2) Power: Addition in the power results sheets of an explanatory text on the "Max speed correction" function ideal in the event of poor GPS reception or failure of this one (indeed, 95% of the measurement accuracy is made by the accelerometer)

 

V 5.1.1

Wed 27/12/2023 - 1.32 am

 

1) Change in precision of pressure units: The hPa remains with a precision of 1 digit after the decimal point, but the in Hg and PSI go from 1 to 2 digits after the decimal point

 

V 5.1

Sat 08/07/2023 - 6.23 pm

 

As part of the porting of the V6 Android version to the V5 iOS version:

1) Addition of the function of power results correction on the measurement end max speed (very useful in the event of poor GPS reception or even GPS failure)

2) Increased the maximum number of results per type (power, accelerations, runs flying start) and per car from 10 to 20

3) Replacement of the old function of automatic recovery of weather data (versions <= 4.1) by a function of manual recovery of these data in real time and by geolocation on the reference weather site "The Weather Channel"

Note: The reasons for this choice are as follows:

- The last weather server used for the automatic recovery of weather data stopped its service overnight, a mishap that I would prefer not to see repeated...

- This type of service is chargeable beyond a certain number of connections per day, which would force me to have to pass on this additional cost to PerfectPower users, whereas it takes no more than... 20 seconds to complete yourself your own weather data (pressure, temperature, and humidity) with the new manual recovery system that I propose, including in particular the automatic conversion of the atmospheric pressure given at sea level (by standardization) into the local pressure on your measurement road: so I think this solution is the most advantageous for everyone!

 

V 5.0

Sat 20/05/2023 - 2.57 pm

 

Upgrade to the level of PerfectPower Android 6.0 on measurement accuracy + minimal but essential adaptations, which includes:

1) All adaptations to iOS 16 (09/2022) + iOS mini changed from 9 (09/2015) to 11 (09/2017)

Validation tests carried out physically on my iPhone 7 running iOS 15.7.5 and in the iOS simulator on iPhone 14 & 14+ & 14 Pro & 14 Pro Max running iOS 16.4 (March 27, 2023)

2) Equalization of the graphic rendering of all screens both horizontally and vertically for ALL iPhones since the 5 (09/2012), the first iPhone to have a 9/16 screen

List of iPhones concerned (classified by type of screen): 5 & 5C & 5S & SE, 6 & 6S & 7 & 8 & SE2 & SE3, 6+ & 6S+ & 7+ & 8+, X & XS & 11 Pro , XR & 11, 12 & 12 Pro & 13 & 13 Pro & 14 & 14 Pro, 11 Pro Max, 12 Pro Max & 13 Pro Max & 14+ & 14 Pro Max

3) Ultimate optimization of power and acceleration measurements accuracy (based on the "Accelerometer + GPS" combination)

A) Accelerometer frequency still limited to 100 Hz (optimal setting), but detection of the starting point still refined

B) Optimization of the end of measurement detection (rev limiter - on petrol engine - or foot lift) (power only)

C) Optimization of the curves processing by the choice of a new, more efficient signal processing technique:

- Filtering of engine vibrations optimized

- Filtering of "road disturbances" optimized

D) Creation of an auto-adaptive smoothing of the curves according to the signal / noise ratio, allowing an optimal precision of curves in all circumstances and the equalization of the precision of curves in 2nd and 3rd gear (power only)

E) Optimization of the PerfectPower model of losses under load on the pneumatic part (power only)

F) Optimization of the PerfectPower model of rolling resistance, adapted to recent road tires (law still of type a + bV², but a and b different: these are now the average values recorded by a European test campaign in 2013 on a very large number of vehicles) (power only)

G) Optimization of the PerfectPower model of engine and wheels inertia calculation (power only):

- The calculation of the engine inertia now takes into account the number of cylinders, which gives more realistic results for all engines with more (or less!) than 4 cylinders: indeed, my old model was based on a study of several PSA (Peugeot & Citroën) 4-cylinders, which could not fully apply to engines with more or less than 4 cylinders, but the shooting is now rectified!

- The calculation of the wheels inertia is refined thanks to the optimization of my model (Renault Clio 16V wheels with aluminum rims), much finer on the geometric schematization of the moving masses.

4) Removal of the function of automatic recovery of weather data, which will be replaced in the next version (5.1) by a function of manual recovery of these data in real time and by geolocation on the reference weather site "The Weather Channel"

Note: The reasons for this choice are as follows:

- The last weather server used for the automatic recovery of weather data stopped its service overnight, a mishap that I would prefer not to see repeated...

- This type of service is chargeable beyond a certain number of connections per day, which would force me to have to pass on this additional cost to PerfectPower users, whereas it takes no more than... 20 seconds to complete yourself your own weather data (pressure, temperature, and humidity) with the new manual recovery system that I propose, including in particular the automatic conversion of the atmospheric pressure given at sea level (by standardization) into the local pressure on your measurement road: so I think this solution is the most advantageous for everyone!

5) Various textual and graphic modifications + Update of all web links (FR/EN guides)

 

Joomla templates by a4joomla